Your success in Juniper Service Provider Routing and Switching JN0-661 Certification exam ensures your professional strength in order to be more successful in future. But you should know the pattern of Juniper Service Provider Routing and Switching exam to perform well in it. PracticeDumpsGuru provides you latest JN0-661 practice exam Questions. The Juniper JN0-661 practice exam dumps material consists of two formates, practice test software and pdf files. Practice test software has a user-friendly interface, which helps you to test your preparation and point out your weak areas. Pdf files consists of latest Juniper JN0-661 exam questions.
♥ VALID JN0-661 Exam Questions 2018 ♥
JN0-661 exam questions, JN0-661 PDF dumps; JN0-661 exam dumps:: https://www.dumpsschool.com/JN0-661-exam-dumps.html (133 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)
Latest Juniper JN0-661 Dumps Exam Questions and Answers:
What must you do to use the Layer 2 interworking interface to connect a BGP Layer 2 VPN with an LDP Layer 2 circuit? (Choose two.)
A. You must configure a policy importing the bgp.l2vpn.0 routing table into the inet.0 routing table.
B. You must enable the I2iw protocol.
C. You must have a Tunnel Services PIC installed to used the L2 interworking interface.
D. You must include the iw0 statement under the [edit interfaces] hierarchy.
Answer: B, D
You are asked to implement a BGP-signaled VPLS network for a new customer. Which two statements are correct regarding this implementation? (Choose two.)
A. A full mesh of LDP sessions between PEs must be configured.
B. The PE routers distribute VPLS-to-label mapping using MP-IBGP.
C. These MP-BGP sessions must be configured to support the I2vpn signaling address family.
D. These MP-BGP sessions must be configured to support the inet-vpn signaling address family.
Answer: B C
Referring to the exhibit, you have configured an L3VPN that connects Site-1 and Site-2 together, but the BGP routes are being hidden on the PE routers. The topology in this scenario is shown below.
Site-1 > PE-1 > P-1 > P-2 > PE-2 > Site-2
Which two acttions would allow communication Site-1 and Site-2? (Choose two.)
A. Disable CSPF on under MPLS on P-1 and P-2.
B. Configure DGP on P-1 and P-2.
C. Enable RSVP for all interfaces on P-1 and P-2.
D. Enable LDP for all interfaces on all routers.
Answer: C, D
A layer 2 circuit (RFC 4447) is established between two PE routers to provide connectivity between two customer sites. Which two statements related to this deployment are true?
A. Kompella encapsulation is used in the data plane communications.
B. LDP must be used for the control plane communications
C. BGP must be used for the control plane communications.
D. Martini encapsulation is used in the data plane communications.
Answer: B, D
Referring to the exhibit, which router will be the RP?
A. R4 for all groups
B. R1 for group 184.108.40.206 and R4 for all other groups
C. R1 for all groups
D. R4 for group 220.127.116.11 and R1 for all other groups
You must ensure that r1’s IPv4 loopback address exists in r3’s inet 0 routing table
Referring to the exhibit, which statement is true?
A. An IPv4 unicast realm can be enabled on each router.
B. A policy can be configured on M to redistribute 172.16.100.1/32 into OSPFv2, which would cause r3 to eventually learn the route and place it into inet0.
C. A RIB group can be configured on r3 to copy that route into inet 0 because 172.16.100.1/32 exists in r3’s inet6.0 table
D. A policy can be configured on r1 to redistribute 172 16 100 1/32 into OSPFv3, which would cause r3 to eventually learn the route and place it into inet 0.
New Updated JN0-661 Exam Questions JN0-661 PDF dumps JN0-661 practice exam dumps: https://www.dumpsschool.com/JN0-661-exam-dumps.html